如果作業完成，那麽小型混凝土攪拌車就會在庫裏閑置，這個時候很多人會覺得都閑置了肯定不會出現什麽問題，然而並不是，小型混凝土攪拌車閑置時要預防生鏽和變形！
If the operation is completed, the small concrete mixer will be idle in the warehouse. At this time, many people will feel that there will be no problem if it is idle. However, it is not. Rust and deformation should be prevented when the small concrete mixer is idle!
小型混凝土攪拌車運行後，須清除外部汙垢，清洗工作機構內的飼料和雜物，要時用水或油清洗，所有潤滑部位須清洗幹淨並重新潤滑。清潔攪拌機後，操作人員還應在攪拌機上塗抹油或貼紙，以減少與空氣接觸的設備氧化的機會。我建議將攪拌機放在涼爽、幹燥、通風的房間內。
After the operation of the small concrete mixer truck, it is necessary to remove the external dirt, clean the feed and debris in the working mechanism, and clean with water or oil when necessary. All lubricating parts must be cleaned and re-lubricated. After cleaning the mixer, the operator should also apply oil or stickers on the mixer to reduce the chance of oxidation of equipment in contact with air. I suggest placing the mixer in a cool, dry and ventilated room.
複雜精密的設備應放置在室內陰涼、幹燥、通風的地方。簡單的設備可以露天存放，但應放在高處、幹燥、無陽光直射的地方。它可以覆蓋一個棚子和所有與地麵直接接觸的部分。用木板或磚塊支撐，重新刷掉掉下來的保護漆。
Complex and precise equipment should be placed indoors in a cool, dry and ventilated place. Simple equipment can be stored in the open air, but should be placed in a high, dry place without direct sunlight. It can cover a shed and all parts in direct contact with the ground. Support with wood or brick, and brush the fallen protective paint again.
小型混凝土攪拌車的彈簧。傳動帶。長柄。由於長期受力或放置不合理，零部件會發生塑性變形，因此在攪拌機框架下應增加適當的支撐點，以減少攪拌機負荷。此外，輪胎、播種管等拆下的零配件應妥善保管，防止擠壓變形。
Spring of small concrete mixer. Drive belt. Long handle. Due to long-term stress or unreasonable placement, plastic deformation of parts will occur, so appropriate support points should be added under the mixer frame to reduce the load of the mixer. In addition, the removed spare parts such as tires and seeding pipes should be properly kept to prevent extrusion deformation.
對於長期停放的小型混凝土攪拌車，應建立登記卡，詳細記錄機器和工具的技術狀況、附件、備件和工具。如果沒有倉庫，當機器停放在室外時，應將電機、傳動帶等易丟失的部件取出，標記並存放在室內。
For small concrete mixer trucks parked for a long time, a registration card shall be established to record the technical conditions, accessories, spare parts and tools of the machines and tools in detail. If there is no warehouse, when the machine is parked outdoors, take out the motor, drive belt and other parts that are easily lost, mark and store them indoors.
如果再次使用的話，就要做好開機前的準備工作，比如：檢查傳動離合器和製動器是否靈活可靠，鋼絲繩是否損壞，履帶輪是否完好，周圍是否有障礙物及各部位潤滑情況等。
If it is used again, it is necessary to make preparations before starting up, such as checking whether the transmission clutch and brake are flexible and reliable, whether the wire rope is damaged, whether the track wheel is in good condition, whether there are obstacles around and the lubrication of all parts.
開機後，要時刻注意攪拌機各部分運轉是否正常。停機時要經常檢查攪拌機的葉片是否彎曲，螺絲是否被敲落或鬆動。更多攪拌車使用事項就來kaiyun網站http://www.skar-bnat.com谘詢了解吧！
After starting, always pay attention to whether all parts of the mixer operate normally. Always check whether the blades of the mixer are bent and whether the screws are knocked off or loose when the machine is stopped. Come to our website for more information about the use of mixer trucks http://www.skar-bnat.com Ask about it!
